Orbit-attitude-vibration coupled dynamics of tethered solar power satellite

A new orbit-attitude-vibration coupled dynamic model of the tethered solar power satellite (Tethered SPS) is established based on absolute nodal coordinate formulation. The Hamilton’s equation of the system is derived by introducing generalized momentum through Legendre transformation. The correctness of the proposed model is verified by an example. The dynamic characteristics of the Tethered SPS are studied using the symplectic Runge-Kutta method. Simulation results show that the orbital radius and the total energy of the system are well preserved. The attitude of the system is unstable when the mass of the bus system is small. However, the attitude stability is dependent on some other parameters of the system, which requires further studies. It is also found that the average tether force/deformation can be roughly estimated by simplifying the solar panel as a particle. The proposed model can be used to study the orbit-attitude-vibration coupled dynamics and control problems.     

SiC/CVD SiC复合涂层的抗氧化及抗热震性能研究

为了提高C/SiC复合材料耐高温性能,采用泥浆浸渍裂解与真空化学气相沉积(CVD)在材料表面制备了SiC/CVD SiC复合涂层,通过XRD、SEM分析了涂层组成与结构;研究了复合涂层的高温抗氧化(700～1 500℃)和抗热震性能。结果表明,泥浆浸渍法制备的SiC涂层具有一定的封孔效果,可使材料开孔率下降,但高温抗氧化效果并不佳,1 200℃氧化10 min后材料弯曲强度保留率下降明显仅有86%。CVD SiC涂层结构致密,与SiC封孔涂层结合较好,在700～1 500℃具有较好的抗氧化效果,随着氧化温度的升高,氧化后涂层完好,表面O元素逐渐增加,材料失重率缓慢增加但不大于0.5%,且材料性能并未下降。涂层材料在1 200℃-10 min短时热震5次后材料弯曲强度保留率仍有95%以上,且未出现开裂、剥落等热震损伤。在1 200℃-30 min长时热震10次后,涂层材料基本被完全氧化,材料失去保护作用,弯曲强度下降至90%左右。     

Six sigma robust design optimization for thermal protection system of hypersonic vehicles based on successive response surface method

Lightweight design is important for the Thermal Protection System(TPS) of hypersonic vehicles in that it protects the inner structure from severe heating environment. However, due to the existence of uncertainties in material properties and geometry, it is imperative to incorporate uncertainty analysis into the design optimization to obtain reliable results. In this paper, a six sigma robust design optimization based on Successive Response Surface Method(SRSM) is established for the TPS to improve the reliability and robustness with considering the uncertainties. The uncertain parameters related to material properties and thicknesses of insulation layers are considered and characterized by random variables following normal distributions. By employing SRSM, the values of objective function and constraints are approximated by the response surfaces to reduce computational cost. The optimization is an iterative process with response surfaces updating to find the true optimal solution. The optimization of the nose cone of hypersonic vehicle cabin is provided as an example to illustrate the feasibility and effectiveness of the proposed method.     

谐振式加速度计自激振荡电路性能评价方法的研究

针对谐振式加速度计成品率不高、精度低等问题，以石英振梁加速度计为例，采用引进标准信号，将谐振电路作为“黑盒子”，对其开展独立的评价。通过评价电路的驱动电压幅值稳定性、移相稳定性、全温幅值/相位对称性等指标，与加速度计实际指标建立了一一对应的关系，为加速度计研制与性能提升提供了有效依据。实际运用表明，电路噪声性能、温度性能大幅提升，产品成品率从70%提高到了约90%。     

基于Ansys Icepak 的负载器热设计与热分析

基于热设计的基础理论与负载器的工作原理，应用Ansys Icepak仿真软件对供配电负载器工作过程中内部散热情况进行仿真，找出负载器内部温度最高部位，指导实际测试，避免实际测试的盲目性。另外，通过优化负载器散热孔设计，降低负载器温升值。     

Orbital stability close to asteroid 624 Hektor using the polyhedral model

We investigate the orbital stability close to the unique L4-point Jupiter binary Trojan asteroid 624 Hektor. The gravitational potential of 624 Hektor is calculated using the polyhedron model with observational data of 2038 faces and 1021 vertexes. Previous studies have presented three different density values for 624 Hektor. The equilibrium points in the gravitational potential of 624 Hektor with different density values have been studied in detail. There are five equilibrium points in the gravitational potential of 624 Hektor no matter the density value. The positions, Jacobian, eigenvalues, topological cases, stability, as well as the Hessian matrix of the equilibrium points are investigated. For the three different density values the number, topological cases, and the stability of the equilibrium points with different density values are the same. However, the positions of the equilibrium points vary with the density value of the asteroid 624 Hektor. The outer equilibrium points move away from the asteroid’s mass center when the density increases, and the inner equilibrium point moves close to the asteroid’s mass center when the density increases. There exist unstable periodic orbits near the surface of 624 Hektor. We calculated an orbit near the primary’s equatorial plane of this binary Trojan asteroid; the results indicate that the orbit remains stable after 28.8375?d.     

基于混杂非对称复合材料的自适应对日定向器

提出并设计了一种基于混杂非对称复合材料层合板的新型自适应对日定向器。该对日定向器采用混杂非对称复合材料层合板作为驱动元件，利用在轨光照条件的变化引起复合材料层合板温度变化，进而使其产生热变形并驱动太阳翼发生偏转。提出的自适应对日定向器结合传统的单自由度对日定向机构，能够实现太阳能帆板的双自由度对日定向。介绍了自适应对日定向器的基本原理，并结合地球静止轨道的光照条件进行了具体设计。利用能量变分原理建立了混杂非对称复合材料的热变形模型，分析其热变形特点，并利用有限元方法对定向器在地球静止轨道上的温度场特性、热变形及对日定向转动角度进行分析。有限元分析结果表明，通过合理设计，自适应对日定向器的转角能够随太阳光入射角变化呈线性变化，定向精度可达±1°。     

星载激光通信终端在轨机动对温度影响

对激光通信终端在轨瞬态温度变化开展了仿真，以期研究在轨机动的影响、热分析和热试验时机动模式的简化模拟。通过合理地分析与简化，建立终端的轨道热分析模型，准确模拟在轨机动，根据典型机动模式、外热流和涂层退化等因素设计了计算工况，得出了终端在轨运行过程中的温度场随时间和姿态变化规律。结果表明：不同机动模式下的温度变化存在差异，最大可达23.0℃，采用固定姿态或一维转动的简化热分析或热试验不能准确模拟实际飞行温度，甚至不能部分替代二维转动热分析或热试验；光学天线和反射镜的温度控制是制约终端工作的瓶颈，为终端设计合适的避光机动策略，可大幅度提高温度稳定度和均匀度。研究结果可以为光机电设备在轨机动策略的设计和改进提供参考。     

点阵结构空气舵及内部流体热流固耦合研究

开展了钛合金TC4材料激光粉末床熔融(LPBF)工艺研究,在此基础上设计了多孔轻质空气舵模型,并基于有限差分法(FDM),采用三维流固耦合共轭传热数值计算方法,利用流体体积法(VOF)追踪流体自由液面,研究了典型的点阵夹层结构的空气舵内部冷却液动态换热过程的相互影响过程,考虑了冷却液与钛合金材料蒙皮间的耦合传热及湍流换热。结果表明,空气舵的内部流体压强随速度的增加而增加,从而导致流体出口的速度增加。当压强增加到一定程度时,流体的出口以水柱形式喷出。虽然较大的流体速度可以带走较多的热量,但是影响远小于对压强的影响。综合考虑空气舵的服役要求,获得了合适的冷却水入口速度。     

高效空间应用燃料电池热能利用技术研究

首先介绍了空间应用燃料电池高效散热及温控技术。高精度控温主要是利用被动散热技术,将产生的热量快速传导至外部冷却介质,从而保证产热面的温度均匀性,实现电池稳定工作。通过嵌入式被动散热和双端散热的冷却方式,实现电堆内部最大温差小于5℃,换热系数达1000W/(m·K)。